Epoxy Resin Clear 30L - Epoxy Supplies
Delivery Australia Wide Daily
Showroom & Warehouse
Queensland / Victoria
1800 437 699FREE CALL

EPO100C® Epoxy Resin Clear 30L

  • Product Code: EPO100C-30
  • Availability: In Stock
  • $660.00

Frequently Asked Questions

What is the difference between EPO100G® Glaze & EPO100C® Clear?

APC Formulate & Manufacture two different forms of clear epoxy resin. It's important you use the correct resin in order to ensure a successful outcome of your project. APC Clear Resin (EPO100C®) is used for high-build applications over 4mm. Such as repairs, mortar & casting. APC Glaze Resin (EPO100G®) is used for roll/pour on applications where the depth of the product is less than 4mm. Using EPO100C® in applications thinner than 4mm will result in adverse effects like Fish-eyeing and bubbling. Glaze in depths over 4mm can appear cloudy/foggy.

Can EPO100® Clear be applied directly to concrete?

For roll on applications, you should use Epoxy Glaze.

How long do I have to work with EPO100C®, should I allow the mix to stand?

All resins manufactured by All Purpose Coatings do not require a standing period in order to allow for the product to begin curing. Once Part A and Part B have been mixed, curing begins immediately. Working time is approximately 40 mins in the bucket depending on the humidity and temperature of the work area.

Does EPO100C yellow when exposed to sunlight?

Whilst Epoxy Glaze is an ultra-clear, low yellowing epoxy, exposure to sunlight will still cause the epoxy to yellow off. In order to prevent this you can apply a UV top coat such as; SPA60, SPA80 or Tetrathane®. Using such top coats will allow the system to be installed outside or inside. Yellowing is not limited to All Purpose Coatings range of epoxies and is a typical property of any manufactured resin system. 

Epoxy Resin Clear EPO100C® 

Key Features

 Suitable Residential, 
   Commercial & Industrial   

  Solvent Free 

  Water Clear at Depth  

100% Solids
  Premium Formulation  

Conforms to APAS 0209

About EPO100C®

EPO100C® Clear is an industrial high performance,100% solids, two-part cycloaliphatic amine-cured epoxy resin manufactured by All Purpose Coatings Pty Ltd.

Designed, formulated and manufactured by All Purpose Coatings, EPO100C® is specifically designed to be used as a binder for epoxy mortar coving, concrete repairs, falls to waste, ramping, encapsulation & casting.

When used in compliance with the Technical Data Sheet EPO100C® will achieve a tensile strength (MPa) greater than concrete itself.

IMPORTANT - EPO100C Clear Epoxy should not be used as a roll coat system, for a roll coat system refer to EPO100G Clear Glaze.

Product Properties              


  • Epoxy Mortar Coving
  • Epoxy Mortar Ramps
  • Government Buildings
  • Falls to Waste
  • Anchoring Resin
  • Encapsulating Resin
  • Casting
  • Concrete Filler & Repairs
  • Binder for Non-Skid Surfaces
  • Floor Coating – Not designed as a roll coat system (Must be poured at depth)
  • Floor Coating - Refer to EPO100G® Glaze if you are looking for a roll coat system
  • Bench Tops – Not designed as a roll coat system (Must be poured at depth)
  • Art Work
  • Food Contact Safe:- Federal Regulations Code


  • No VOC's (Volatile Organic Compounds)
  • Solvent Free
  • Low Viscosity
  • User Friendly
  • High gloss
  • Self-leveling
  • Excellent adhesion
  • Chemical resistant
  • High build application
  • Abrasion Resistant
  • Bond strength stronger than concrete

Spread Rate: 1L / 1m2 = 1mm in depth

Casting: Maximum 10-15mm in depth without exceeding 15L per Pour

*Maximum 15L mix is advised for large pours. Substrate must be primed & sealed with EPO100C prior to conducting a pour. 
* When completing a pour in stages the waiting time is around 2 - 3 hours or until it is firm/ is in the gel stage.
* DO NOT POUR MULTIPLE MIXES AS A SINGLE POUR All epoxies will reach a higher temperature when conducting larger pours.
* Read the TDS and SDS prior to use.
*Devices such as digital cameras,computer monitors, printers, and scanners produce colour differently. Therefore, the sample or product may not look exactly like the image that you see on your screen. 
*Coverage rates for coatings are based on smooth dense surfaces. The surface texture and porosity of the concrete can vary considerably and allowances should be made for this.

Kit 1 x 20L Epoxy Resin Clear EPO100C 1 x 10L Epoxy Hardener EPO100CH

Write a review

Note: HTML is not translated!
    Bad           Good