EPO100® Epoxy Resin Clear 6L

Product Code: EPO100C-06
Availability: In Stock
Qty:     - OR -   Add to Wish List

Epoxy Resin Clear 100% Solids:

This High Performance Industrial Epoxy is a 100% solids, two-pack cycloaliphatic amine cured epoxy resin matrix. USDA acceptable (for incidental food contact) epoxy flooring resin designed as a binder for non-skid surfaces. It is non-blushing and non-water spotting, high gloss, self-levelling.

-         No VOC's (Volatile Organic Compounds)

-         Low Viscosity

·         Non-blushing

·         Non-water spotting

·         High gloss

·         Self-levelling

·         Excellent adhesion

·         Chemical resistant

·         High build application

·         Abrasion Resistant

·         Bond strength stronger than concrete

Designed for use in a wide range of commercial environments where a lasting solution to floor maintenance problems is required. The exceptional resistance to a wide variety of chemical spillage and fumes makes this product ideal for use in high traffic commercial environments.

Please read our Information sheet to understand the differences between Epoxies and how to distinguish between a high quality product such as EPO100 and a lesser quality product. Epoxy General 2013

Please read the TDS and SDS prior to using our products.

Epoxy can be applied using:


Surface Preparation.

Surfaces must be clean, dry and free from all traces of loose material, old coatings, curing compounds, release agents, laitance, oil and greases etc. 


  • As a Primer we recommend thinning the first coat with up to 20% Epoxy Thinners to ensure high penetration and adhesion. Second coat thin up to 10% Epoxy Thinners. Pot life for a 10 lt batch is approximately 40 minutes at 25 deg.C, so mix only the amount of epoxy that can be easily applied within that time limit. Apply using a brush, or roller. Use a lint free epoxy roller to apply the product.
  • As a Binder Silica Sand can be added to make a Mortar blend or Ceramic to make Crack repair. Using trowel for high build or Spatula for crack filling with Ceramic.
  • As a Clear Filler, just mix and pour.
  • When placing Mortar a Primer should be used before installation.
  • Mortar can be sealed with roll coats 24 hours after installation.
  • Refer to Mortar Data sheet for self level or high build mixing quantities.
  • For self level Ceramic or -250 Slica Sand can be used.
  • For Mortar up to 8 Parts Silica Sand -1 + 250 can be added.
  • Mortar should be wet trowel to compress sand.
  • If using Trowel or Coving tool use small amount of Thinners to keep Trowel wet. Shake off  excess Thinners before use.

Mixing Instructions.

Mix Part ‘A’ thoroughly using a power drill with paint mixing attachment.

Mix 2 parts ‘A’ with 1 part ‘B”.

Mix thoroughly using a power drill with paint mixing attachment for 2 minutes, ensuring sides are well mixed.

If using as a Binder mix appropriate amount of Sand or Ceramic to achieve desired level of slump or self level.

Always wear a mask and avoid breathing vapors of resin or dust residue.

Technical Description
Solids Content 100% ww
Pot Life 30 - 45 minutes, depending on temperature.
Tack Free Time 12 Hours
Re-Coat 12 - 48 Hours
Initial Hardening 24 Hours @ 25 Degrees
Full Chemical Cure 7 Days @ 25 Degrees
Film Thickness Varies depending on process.
Coverage Rate 1L per 1m2 = 1mm in depth per volume mixed.
Serviceable Life 5 - 10 Years
Recommended Uses
Garage, Factories & Workshops, Warehouses, Loading Bays, Washrooms, Food Prep Areas/Processing Plants etc.

*Coverage rates for coatings are based on smooth dense surfaces. The surface texture and porosity of the concrete can vary considerably and allowance should be made for this.

Kit 1 x 4L Epoxy Resin Clear PART A EPO100C 1 x 2L Epoxy Hardener PART B EPO100C

Write a review

Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below: